29.6V 40Ah 8S Semi-Solid-State Lithium Battery for High-Power UAV and RC Applications
Quick Specifications
|
Item |
Specification |
|
Product Type |
High-Discharge Semi-Solid-State Lithium Battery |
|
Configuration |
8S1P |
|
Nominal Voltage |
29.6V |
|
Rated Capacity |
40Ah / 40000mAh |
|
Nominal Energy |
Approx. 1.184kWh calculated |
|
Battery Chemistry |
Semi-Solid-State NCM Lithium Battery |
|
Continuous Discharge Rate |
3C |
|
Continuous Discharge Current |
Approx. 120A |
|
Peak Discharge Rate |
5C |
|
Peak Discharge Current |
Approx. 200A |
|
Peak Duration |
Up to 10 seconds |
|
Main Connector |
QS8 High-Current Connector |
|
Balance Connector |
Multi-pin 8S Balance Connector |
|
Cable |
Heavy-Gauge Red / Black Power Cable |
|
Configuration |
8S1P |
|
Approx. Dimensions |
200 × 88 × 84mm* |
|
Approx. Weight |
3.4kg* |
|
Carrying Feature |
Integrated Fabric Strap |
|
Typical Applications |
UAV, Industrial Drone, High-Power RC and Mobile Platforms |
What Is a 29.6V 40Ah Semi-Solid-State Battery?
A 29.6V 40Ah semi-solid-state lithium battery is a high-energy, high-discharge battery pack designed for applications requiring considerably more power and runtime than conventional small RC battery packs.
This 8S1P battery provides 40Ah / 40000mAh capacity and approximately 1.184kWh of nominal energy based on 29.6V × 40Ah.
Unlike a conventional low-capacity hobby battery, this platform combines large pouch-cell capacity, a high-current QS8 connector, heavy-gauge discharge cables and an 8S balance connection.
As a semi-solid-state lithium battery manufacturer, the battery is designed around applications where three requirements matter simultaneously:
- High gravimetric energy density
- High continuous current capability
- Compact battery volume
The product is particularly relevant to high-power UAV, industrial drone and customized unmanned-system projects where battery weight directly affects payload, flight time and system efficiency.
Key Features
40Ah High-Capacity 8S Battery Architecture
The battery uses an 8S1P configuration with 40Ah rated capacity, giving the pack approximately 1.184kWh of nominal energy when calculated at 29.6V.
As a 29.6V 40Ah lithium battery manufacturer, this configuration is positioned above typical small RC battery packs and is more suitable for platforms requiring longer operating time and significantly higher stored energy.
The single-parallel architecture can also reduce the complexity associated with connecting multiple smaller packs to reach the same capacity.
3C Continuous Discharge for High-Power Loads
The battery is specified for a 3C continuous discharge rate.
For a 40Ah battery:
40Ah × 3C = approximately 120A continuous current
At 29.6V nominal voltage, that represents approximately:
29.6V × 120A = 3.55kW DC nominal electrical output
As a high-discharge UAV battery supplier, this current capability is relevant for propulsion systems requiring sustained high power rather than short-duration low-current operation.
Actual output capability still depends on battery temperature, SOC, connector resistance, cable design and final system conditions.
Up to 5C Peak Discharge
The customer-facing specification provides a 5C peak discharge rate for up to 10 seconds.
For a 40Ah battery:
40Ah × 5C = approximately 200A peak current
This gives the battery additional short-duration current capability during conditions such as:
- UAV takeoff
- Rapid acceleration
- High-load maneuvering
- Temporary motor load increases
- Short high-power operating events
As a high-current lithium battery manufacturer, peak-discharge capability should always be matched to the motor controller, connector, cable and thermal design of the complete system.
High-Energy-Density Semi-Solid-State Cell Platform
The engineering source identifies a 340Wh/kg cell-level energy density under its specified test condition.
This is particularly relevant for weight-sensitive applications.
As a high energy density battery manufacturer, reducing battery mass for a given energy requirement can potentially allow system designers to allocate more weight to payload, sensors, structural components or longer operating endurance.
The 340Wh/kg figure should be presented as a cell-level specification, not the finished pack-level energy density.
QS8 High-Current Connector and Heavy-Gauge Cable
The battery uses a QS8 high-current connector combined with thick red and black discharge cables.
This type of connection architecture is designed for applications involving substantially higher current than common small RC connectors.
As an OEM high-power lithium battery supplier, connector type, cable length, cable gauge and polarity configuration can be customized according to the customer's controller, power-distribution board or vehicle architecture.
OEM Battery Engineering for High-Power Platforms
This battery should not be positioned only as a fixed catalog product.
As a custom semi-solid-state battery manufacturer, the platform can be engineered around:
- Voltage
- Capacity
- Discharge current
- Cell configuration
- Connector
- Cable length
- Balance connector
- Battery dimensions
- Weight targets
- Strap design
- Label and branding
- Discharge-rate requirements
This is particularly valuable for UAV and unmanned-system manufacturers where the battery compartment, center of gravity, motor system and maximum takeoff weight must be considered together.
Technical Specifications
|
Category |
Parameter |
Specification |
|
Battery |
Chemistry |
Semi-Solid-State NCM Lithium |
|
Battery |
Configuration |
8S1P |
|
Battery |
Nominal Voltage |
29.6V |
|
Battery |
Rated Capacity |
40Ah |
|
Battery |
Rated Capacity |
40000mAh |
|
Battery |
Calculated Nominal Energy |
Approx. 1184Wh |
|
Discharge |
Continuous Discharge Rate |
3C |
|
Discharge |
Continuous Discharge Current |
Approx. 120A |
|
Discharge |
Peak Discharge Rate |
5C |
|
Discharge |
Peak Current |
Approx. 200A |
|
Discharge |
Peak Duration |
Up to 10 seconds |
|
Connector |
Main Connector |
QS8 |
|
Connector |
Balance Connector |
8S Multi-Pin Balance Connector |
|
Cable |
Main Power Leads |
Heavy-Gauge Red / Black |
|
Mechanical |
Approx. Dimensions |
200 × 88 × 84mm* |
|
Mechanical |
Approx. Weight |
3.4kg* |
|
Mechanical |
Carrying Strap |
Included |
|
Cell Data |
Cell Model |
ULi9596210 |
|
Cell Data |
Cell Capacity |
40Ah |
|
Cell Data |
Cell Energy Density |
340Wh/kg at specified test condition |
|
Cell Data |
Cell Internal Resistance |
Approx. 1.0mΩ |
|
Cell Data |
Cell Weight |
410 ±20g |
|
Cell Data |
Standard Charge / Discharge Rate |
0.5C |
|
Cell Data |
Maximum Continuous Charge Rate |
2C |
|
Cell Data |
Maximum Continuous Discharge Rate |
5C under specified condition |
|
Cell Data |
Pulse Discharge Rate |
10C under specified condition |
|
Cell Data |
Cell Voltage Range |
4.25V–2.5V |
|
Cell Data |
Cycle Life |
1000 cycles at 0.5C / 1C condition |
|
Cell Data |
High-Rate Cycle Life |
500 cycles at 0.5C / 3C condition |
|
Safety |
Cell Safety Reference |
GB 38031-2025 stated in source sheet |
Applications
Agricultural Drones
High-capacity battery packs can be used in agricultural UAV systems where aircraft must carry both propulsion batteries and operating payloads such as spraying equipment.
As a drone lithium battery supplier, capacity, discharge current and battery weight can be optimized according to the aircraft's payload and mission duration.
Heavy-Lift UAV and Industrial Drones
As an industrial UAV battery manufacturer, this 29.6V 40Ah battery can be evaluated for unmanned aircraft requiring high energy capacity and sustained current output.
Its combination of approximately 1.184kWh nominal energy and 120A continuous current makes it relevant to larger UAV platforms where both endurance and propulsion power matter.
Battery selection should always be based on motor power, ESC rating, propeller configuration, maximum takeoff weight and required flight time.
Mapping and Surveying UAVs
Surveying and mapping platforms often require stable power over longer missions while carrying cameras, LiDAR or other sensors.
A high-energy-density battery platform can help improve the energy available per unit of battery mass.
Large RC Vehicles and Experimental Platforms
The 8S voltage platform and QS8 connector also make this battery suitable for evaluation in high-power customized RC platforms, unmanned ground vehicles and experimental electric systems requiring high current.
Compatibility must be confirmed against the ESC, motor and voltage limits of the target platform.
Inspection and Security Drones
Industrial inspection UAVs used for power lines, infrastructure, construction, energy facilities and security operations can require higher battery capacity than small consumer drones.
As an OEM UAV battery supplier, connector, cable and pack dimensions can be matched to the aircraft's electrical and mechanical design.
Robotics and Unmanned Mobile Equipment
The battery can also be evaluated for mobile robotic equipment requiring a compact, high-energy battery combined with high current capability.
For robotic projects, dimensions, continuous load, peak load and thermal conditions should be confirmed before final pack design.
Semi-Solid-State NCM vs LiFePO4 vs Lead-Acid
Because this product uses a semi-solid-state NCM platform, a three-way comparison is more relevant than comparing only LiFePO4 with lead-acid.
|
Comparison |
Semi-Solid-State NCM |
LiFePO4 |
Lead-Acid |
|
Primary Advantage |
High energy density |
Long cycle life and thermal stability |
Low initial cost |
|
Gravimetric Energy Density |
High |
Medium |
Low |
|
Suitability for Weight-Sensitive UAVs |
Strong |
Moderate |
Poor |
|
High-Discharge Capability |
Strong when properly designed |
Strong depending on cell type |
Limited |
|
Battery Weight for Equivalent Energy |
Lower |
Medium |
High |
|
Pack Size for Equivalent Energy |
Smaller |
Medium |
Larger |
|
Cycle Life |
Medium to High depending on design |
Usually high |
Lower |
|
Thermal Stability |
Requires robust design and management |
Generally strong |
Mature but heavy |
|
Voltage per Cell |
Higher |
Lower |
Approx. 2V per cell |
|
BMS Requirement |
Strongly recommended |
Strongly recommended |
Usually simpler |
|
Fast Charge Potential |
Good depending on cell specification |
Good |
More limited |
|
UAV Suitability |
Excellent for energy-density-driven projects |
Suitable where cycle life and safety dominate |
Generally unsuitable |
|
Stationary Energy Storage |
Possible |
Very common |
Common in legacy systems |
|
Cost |
Higher |
Medium |
Lower |
|
Best Fit |
UAV, aviation, high-power mobile systems |
ESS, industrial, mobility |
Cost-sensitive stationary/legacy systems |
The exact performance of each chemistry depends on cell design, SOC window, temperature, discharge rate and battery management strategy.
Customization Options
|
Customization Item |
Standard Reference |
OEM / ODM Options |
|
Voltage |
29.6V / 8S |
Alternative series configuration |
|
Capacity |
40Ah |
Project-specific capacity |
|
Chemistry |
Semi-Solid-State NCM |
Cell platform subject to application |
|
Continuous Discharge |
3C |
Can be engineered according to load |
|
Peak Discharge |
5C / 10s |
Customized according to cell and thermal design |
|
Main Connector |
QS8 |
XT90, AS150, Anderson or customer-specified |
|
Balance Connector |
8S Multi-Pin |
Customized connector |
|
Cable Gauge |
High-Current Cable |
Customized according to current |
|
Cable Length |
Standard |
Customized |
|
Dimensions |
Reference configuration |
Customized to battery compartment |
|
Pack Shape |
Rectangular |
Custom mechanical structure |
|
Strap |
Integrated |
Customized strap / handle |
|
Label |
Standard Product Label |
OEM branding |
|
Voltage / Current Monitoring |
Basic Pack |
Smart monitoring can be evaluated |
|
Communication |
Not shown as standard |
CAN / UART / RS485 can be evaluated for custom projects |
|
Packaging |
Standard |
OEM packaging |
|
Certifications |
Project dependent |
Evaluated according to destination market |
FAQ
-
1. What is the nominal energy of this 29.6V 40Ah battery?
-
2. What does 8S1P mean?
-
3. What is the continuous discharge current?
-
4. What is the peak discharge current?
-
5. Why use semi-solid-state cells for UAV batteries?
-
6. What connector does this battery use?
-
7. Can this battery be used directly with any 8S drone?
-
8. What is the difference between this battery and a normal LiPo battery?
-
9. Can the connector, dimensions and cable length be customized?
-
10. What information is required for an accurate OEM quotation?
Battery Testing and Quality Control
Each AOVOLT electric motorcycle lithium battery pack is tested before shipment to support safety, performance consistency and reliable mass production. The testing process helps verify cell quality, BMS protection, voltage accuracy, capacity performance, charge-discharge stability and final packing condition.

Certifications and Compliance
For international B2B orders, AOVOLT can support lithium battery shipping and compliance documents according to product configuration and destination market requirements.
Available documents may include MSDS, RoHS, UN38.3, CE or other project-based documents. Required documents should be confirmed before sample approval or bulk production.
Factory Service
Power upgrade, zero maintenance cost
ODM & OEM Customization, One-stop Solution, Strict Quality Assurance.
inquiry now
Other products
Send inquiry
description2

E-Mobility Battery
Lead Acid Replacement Battery
Drone Battery
Energy Storage System
Industrial & Robot Battery
Custom Battery Pack
Tool Replacement Battery
Electric Mobility Battery
Drone Battery
Energy Storage Battery
Lead-to-Lithium Battery
Robot Battery
Custom Battery Pack
Tool and Garden Tool Battery











